Pass Cisco 200-601 Exam Easily With Questions And Answers PDF

VCE-Braindumps understands the importance of all key topics of Cisco Certified Network Associate Industrial 200-601 exam so that we prepare 200-601 exam dumps material is prepared according to the 200-601 exam pattern. You feel in the actual Cisco 200-601 exam confident enough to attempt each 200-601 exam question perfectly. Just check the 200-601 exam free demo first to have an idea what exactly VCE-Braindumps has prepared for you and offering with Money Back Guarantee!

Version: 9.0
Question: 1

Exhibit:

Refer to the exhibit. Which port should a PLC with IP address 192.168.3.65 be plugged into in order to communicate to the rest of the network?

A. FastEthernet1/1
B. FastEthernet1/2
C. FastEthernet1/3
D. FastEthernet1/4
E. FastEthernet1/5

Answer: C

Question: 2

Which option allows an EtherNet/IP I/O device to be safely installed where it is subject to water immersion?

A. The device is rated IP20 and the power wiring is installed securely to the terminal block.
B. The device is rated IP67 and a power cordset is used.
C. The device is rated IP67 and immersed to 10 m.
D. The device is rated IP20 and immersed to 10 m.

Answer: B

Question: 3

New Updated 200-601 Exam Questions 200-601 PDF dumps 200-601 practice exam dumps: https://www.dumpsschool.com/200-601-exam-dumps.html (70 Questions)

Refer to the exhbit. Which three elements would enable high availability and predictable performance for a motion control application spread across two switches (with video and I/O traffic)? (Choose three)

A. Configure QoS to give PTP traffic the highest priority
B. Fiber optic uplinks
C. Redundant uplinks
D. Configure QoS to give I/O traffic the highest priority
E. Copper uplinks
F. Interconnect the two switches

Answer: A, B, C

Question: 4

You have been tasked to design an Ethernet network capable of Motion control with cycle times not to exceed 1ms. In order to create a more deterministic network, what characteristic/s should you primarily focus on?
A: Lattency and Jitter
B: Redundancy and high availability
C: Explicit and Implicit messaging
D: This cycle time is not possible on an Ethernet network
E: Gigabit port speed
Answer: A

Question: 5
Refer to the exhibit.

CIP Implicit messages from I/O#1 are being marked IP DSCP 47 by the endpoint and this marking is trusted by L2SW4. L2SW4 is configured to map DSCP 47 to output queue 1 threshold 1. You have received feedback that some of these messages are not being received. Executing the show mls interface GigabitEthernet statistics command on L2SW4 results in:
L2SW4# show mls interface GigabitEthernet 1/1 statistics

output queues dropped:
queue: threshold1 threshold2 threshold3
queue 0 0 0 0
queue 1 309232345 450 0
queue 2 300 10 0
queue 3 91 0 0
Repeating this command results in the counters incrementing for queue 1 threshold 1. What are two options for reducing the packet loss on this interface while preserving the end-to-end DSCP marking? (Choose two)

A. Configure I/O#1 to mark this traffic with a different DSCP that is mapped to a less congested queue
B. Increase the buffer allocation for input queue 1
C. Increase the buffer allocation for output queue 1
D. Alter the service policy to police to a higher CIR
E. Change the egress queue map on L2SW4 to map this traffic to a less congested queue

Answer: C, E

Question: 6

It is common to use Resilient Ethernet Protocol (REP) on the manufacturing floor as a resiliency protocol, as opposed to the Enterprise where it is not generally deployed. What are two reasons why REP is more suitable for the plant floor? (Choose two)

A. REP is only supported on Industrial Ethernet switches, it is not supported on Catalyst switches.
B. REP converges faster than Spanning Tree, allowing for greater network availability.
C. REP supports Industrial Ethernet protocols better because it moves the packets faster.
D. Running dual cables from access switches to an aggregation switch can have a much higher cost on the plant floor than in the Enterprise and running a ring protocol like REP provides resiliency at a lower cost.
E. Industrial protocols can be negatively impacted by the number of nodes the Ethernet frame traverses, REP provides a topology with no more than 3 nodes for any data path.

Answer: B, D